Scholarlink

<p>Polymethyl methacrylate (PMMA) is a biocompatible polymer widely used in prosthetic applications, yet its limited stiffness and strength restrict its performance under the cyclic loads imposed by lower limb prosthetic feet. This study investigates the combined effect of Al₂O₃ nanoparticle reinforcement and post-fabrication heat treatment on the mechanical and structural performance of PMMA-based nanocomposites for prosthetic foot applications. Nanocomposite samples containing 0, 2.5, 5, 7.5, and 10 wt% α-Al₂O₃ nanoparticles were fabricated using a silane-assisted compounding route and subsequently annealed at 80&#xa0;°C, 110&#xa0;°C, and 140&#xa0;°C for 15&#xa0;min. XRD confirmed the phase stability of the α-Al₂O₃ reinforcement and the absence of new crystalline reaction products, while scanning electron microscopy (SEM) revealed progressive densification of the particle–matrix interface up to 110&#xa0;°C. The optimal formulation, P7.5&#xa0;A annealed at 110&#xa0;°C, in which the optimal Young’s modulus and a compressive yield strength have been achieved, representing improvements of + 71.1% and + 22.2%, respectively, over neat PMMA. A finite element model (FEM) of a prosthetic foot was developed in ANSYS. FEM results showed that P7.5&#xa0;A/110°C reduced total structural deformation by 40.2% relative to neat PMMA. These findings demonstrate that PMMA reinforced with 7.5 wt% Al₂O₃ and annealed at 110&#xa0;°C offers a well-balanced combination of stiffness, strength, and structural safety suitable for lower limb prosthetic foot applications.</p>

错误：搜索内容不能为空，请输入英文关键词
错误：关键词超出字数限制，请精简
高级检索

Effect of Al₂O₃ nanoparticle reinforcement and annealing on PMMA composite performance for prosthetic feet

  • 期刊论文

  • 出版模式：

    开放获取

  • 发表日期：

    2026年6月29日

查看全文
  • Thamer Albahkali,
  • Hany S. Abdo,
  • Ahmed Algahtany,
  • Talal T. Alshammari,
  • Ahmed Fouly

摘要

Polymethyl methacrylate (PMMA) is a biocompatible polymer widely used in prosthetic applications, yet its limited stiffness and strength restrict its performance under the cyclic loads imposed by lower limb prosthetic feet. This study investigates the combined effect of Al₂O₃ nanoparticle reinforcement and post-fabrication heat treatment on the mechanical and structural performance of PMMA-based nanocomposites for prosthetic foot applications. Nanocomposite samples containing 0, 2.5, 5, 7.5, and 10 wt% α-Al₂O₃ nanoparticles were fabricated using a silane-assisted compounding route and subsequently annealed at 80 °C, 110 °C, and 140 °C for 15 min. XRD confirmed the phase stability of the α-Al₂O₃ reinforcement and the absence of new crystalline reaction products, while scanning electron microscopy (SEM) revealed progressive densification of the particle–matrix interface up to 110 °C. The optimal formulation, P7.5 A annealed at 110 °C, in which the optimal Young’s modulus and a compressive yield strength have been achieved, representing improvements of + 71.1% and + 22.2%, respectively, over neat PMMA. A finite element model (FEM) of a prosthetic foot was developed in ANSYS. FEM results showed that P7.5 A/110°C reduced total structural deformation by 40.2% relative to neat PMMA. These findings demonstrate that PMMA reinforced with 7.5 wt% Al₂O₃ and annealed at 110 °C offers a well-balanced combination of stiffness, strength, and structural safety suitable for lower limb prosthetic foot applications.